SawStop CB31230 Uživatelský manuál

10” INDUSTRIAL CABINET SAWModels CB31230, CB33230, CB51230,CB53230, CB53480, CB73230, CB73480OWNER’S MANUALSawStop®Cabinet Saw Manual 1st Reprint.i1

8 SawStop 10” Industrial Cabinet SawWarning LabelsWarning labels are mounted on the front, rear and side of the saw, on the table insert, and on th

98 SawStop 10” Industrial Cabinet SawIndexIInsert (see Table Insert)Interlock Switch(es): 7, 26, 31KKerf: 21, 35, 62, 67Kickback: 8, 20, 37, 39, 76

SawStop 10” Industrial Cabinet Saw 99IndexRetraction: 10, 12, 45, 57Rip cutting: 34, 38-39, 46, 75 fence: 7, 16, 20, 34, 37-39, 46 narrow rip cu

100 SawStop 10” Industrial Cabinet SawIndexTopCote®: 16, 68TopSaver™: 16, 68Troubleshooting: 69-72Trunnion Brace: 19, 57UUnpacking Your Saw: 13Usin

Cabinet Saw Manual 1st Reprint.i1 1 3/9/2010 8:33:15 AM

SawStop, LLC9564 S.W. Tualatin RoadTualatin, Oregon 97062www.sawstop.comphone 503-570-3200fax 503-570-3303email: [email protected] 2010Cabinet Saw

SawStop 10” Industrial Cabinet Saw 9(On saws with 230V, single phase motors.)(On saws with 230V, three phase motors.) (On saws with 480V, three pha

10 SawStop 10” Industrial Cabinet SawThe SawStop Safety SystemThis table saw is equipped with the SawStop® safety system. This revolutionary techno

SawStop 10” Industrial Cabinet Saw 11The SawStop® safety system does not interfere with your use of the table saw in any way. You can still make al

12 SawStop 10” Industrial Cabinet Saw9. Never install the blade backwards. The brake might not stop a blade that is installed backwards, therefore

SawStop 10” Industrial Cabinet Saw 13Unpacking Your SawUse care when unpacking your saw to prevent damage to any of the saw components or accessori

14 SawStop 10” Industrial Cabinet SawGet to Know Your SawThe major components of your saw are identied below. Make sure you can identify these com

SawStop 10” Industrial Cabinet Saw 15Get to Know Your Saw20. Front Trunnion Bracket21. Front Trunnion22. Rear Trunnion Bracket23. Rear Trunnion2

16 SawStop 10” Industrial Cabinet SawSetting Up Your Saw1. Saw Placement:Position the saw on a level surface away from sources of moisture and ele

SawStop 10” Industrial Cabinet Saw 17Setting Up Your Saw5. Tilt Hand Wheel Handle Installation:Install the handle on the tilt hand wheel b

The saw shown on the front cover includesthe optional 36” fence and extension table. Your saw may look different.Copyright, SawStop, LLCAll Rights Res

18 SawStop 10” Industrial Cabinet SawWARNING! Never install the blade backwards. The brake might not stop a blade that is installed backwards, the

SawStop 10” Industrial Cabinet Saw 19Setting Up Your SawNote: some users may nd it easier to adjust the brake position by opening the motor cover

20 SawStop 10” Industrial Cabinet SawCAUTION! Always spin the blade by hand after changing the blade or the brake cartridge, or after adjusting the

SawStop 10” Industrial Cabinet Saw 21Setting Up Your SawNote: when using a dado set, neither the blade guard nor the riving knife may be used. Inst

22 SawStop 10” Industrial Cabinet Saw9. Table Insert Installation:Your saw is shipped with a high-quality, zero-clearance table insert. The insert

SawStop 10” Industrial Cabinet Saw 23Setting Up Your SawWARNING! Some types of dust created by sawing, power sanding, grinding, drilling

24 SawStop 10” Industrial Cabinet SawWARNING! This saw must be connected to a grounded metal permanent wiring system, or to a system havin

SawStop 10” Industrial Cabinet Saw 25Setting Up Your Sawarbor should spin counter-clockwise when viewed from the right side of the saw.Setting Up Y

26 SawStop 10” Industrial Cabinet SawSetting Up Your SawIn addition, the disconnect switch can be locked in the OFF position with a padlock or simi

SawStop 10” Industrial Cabinet Saw 27Using Your SawUsing Your Saw1. Adjusting the Blade Height:The height of the blade can be adjusted from 1/8 in

SawStop 10” Industrial Cabinet Saw 1To Our CustomersThank you for purchasing a SawStop cabinet saw! It is the safest, most advanced table saw ever

28 SawStop 10” Industrial Cabinet Saw3. Turning on Main Power and Starting the Motor:Your SawStop® saw is equipped with an Electrical Disco

SawStop 10” Industrial Cabinet Saw 29Using Your SawIt is not necessary to turn off the Main Power switch after pushing in the Start/Stop paddle to

30 SawStop 10” Industrial Cabinet Saw4. System Status Codes:In the event that the safety system detects an error, the LEDs on the Switch Box will

SawStop 10” Industrial Cabinet Saw 31Using Your SawSystem Initializing — this code indicates that the system is performing self-checks and charging

32 SawStop 10” Industrial Cabinet SawContact was Detected During Standby — this code indicates that the safety system detected contact with the bla

SawStop 10” Industrial Cabinet Saw 33Using Your SawWARNING! Never run the saw in Bypass Mode unless necessary to cut conductive materials. The brak

34 SawStop 10” Industrial Cabinet Saw6. Using the Blade Guard: Using the blade guard is one of the most important steps you can take to prevent in

SawStop 10” Industrial Cabinet Saw 35Using Your Saw8. Using the Miter Gauge:The miter gauge included with your saw allows you to easily make miter

36 SawStop 10” Industrial Cabinet SawA guide plate is mounted on the end of the main bar (see Fig. 32) and ts in the bottom of the slots to hold t

SawStop 10” Industrial Cabinet Saw 37Using Your SawUsing Your Saw9. Cross-Cutting: Cross-cutting or cutting perpendicular to the grain of the work

2 SawStop 10” Industrial Cabinet SawTable of ContentsWarranty 5No Warranty of Safety 5If You Have an Accident 5Safety 6WARNINGS

38 SawStop 10” Industrial Cabinet SawUsing Your Saw10. Rip Cutting:Rip cutting or cutting with the grain of the workpiece must be performed with a

SawStop 10” Industrial Cabinet Saw 39Using Your SawUsing Your SawContinue pushing the workpiece toward the back of the saw until it clears the anti

40 SawStop 10” Industrial Cabinet SawUsing Your Saw11. Changing the Brake Cartridge:The SawStop standard brake cartridge (shown in Fig. 38) includ

SawStop 10” Industrial Cabinet Saw 41Using Your SawIf the brake cartridge has been actuated, the brake will be locked onto the blade or dado set. I

42 SawStop 10” Industrial Cabinet SawYou can change the brake cartridge either from the top of the saw through the table opening, or from the right

SawStop 10” Industrial Cabinet Saw 43Using Your SawIf the Cartridge has been Actuated: If the cartridge is being replaced because it has been actu

44 SawStop 10” Industrial Cabinet SawInstalling a Brake Cartridge: To install a brake cartridge, the above process is reversed. Align the mounting

SawStop 10” Industrial Cabinet Saw 45Using Your SawWhat to do if the SawStop Safety System ActivatesWhen the SawStop Safety System is activated, th

46 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawWARNING! Always make sure that both the Disconnect Switch and the Main Power

SawStop 10” Industrial Cabinet Saw 47Adjusting Your SawMaking Adjustments to Your SawSet the dial indicator to zero. Slide the dial test indicator

SawStop 10” Industrial Cabinet Saw 3Table of ContentsUsing Your Saw 27 1. Adjusting the Blade Height: 27 2. Adjusting the Blade Tilt Angle:

48 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawTo adjust the alignment, begin by loosening the 4 mounting bolts (see Fi

SawStop 10” Industrial Cabinet Saw 49Adjusting Your SawAlternate Table Alignment ProcedureFor this procedure you will need a set of calipers or a c

50 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your Saw2. Aligning the Blade Elevation Assembly:The blade elevation assembly controls

SawStop 10” Industrial Cabinet Saw 51Adjusting Your SawMaking Adjustments to Your SawThis procedure requires two measurements. For the rst measure

52 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawOnce the set screws are loosened, the eccentric bushing should be free to turn.

SawStop 10” Industrial Cabinet Saw 53Adjusting Your SawMaking Adjustments to Your SawThe geometry involved in this alignment procedure is tricky. T

54 SawStop 10” Industrial Cabinet SawTo do this, set the tilt angle back to 0° and reposition the dial test indicator as described above. When you

SawStop 10” Industrial Cabinet Saw 55Adjusting Your SawMaking Adjustments to Your SawReposition the dial test indicator toward the front of the saw

56 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawUpper Elevation Limit StopTo check the position of the upper elevation limit sto

SawStop 10” Industrial Cabinet Saw 57Adjusting Your SawLower Elevation Limit StopTo check the position of the lower elevation limit stop, remove th

4 SawStop 10” Industrial Cabinet SawTable of ContentsMaintenance 68 1. SawStop Safety System: 68 2. Cabinet: 68 3. Elevation and Tilt M

58 SawStop 10” Industrial Cabinet Saw5. Adjusting the Tilt Limit Stops and Tilt Angle Indicator:The tilt limit stops allow you to easily and quick

SawStop 10” Industrial Cabinet Saw 59Adjusting Your SawTilt Angle IndicatorThe tilt angle indicator is located at the front of the cabinet, just be

60 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawThe head of the bolt is painted yellow for easy identication. To adjus

SawStop 10” Industrial Cabinet Saw 61Adjusting Your SawMaking Adjustments to Your SawTo set the height of the insert, rst remove the lock-down scr

62 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your SawNext, loosen the horizontal positioning bolts using an 8 mm hex L-wrench. Loosen

SawStop 10” Industrial Cabinet Saw 63Adjusting Your SawRemove the blade and set it aside for a moment. Tighten the horizontal positioning bolts. Re

64 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your Saw8. Adjusting the Quick-Release Clamp:The clamping pressure of the spreader / ri

SawStop 10” Industrial Cabinet Saw 65Adjusting Your Saw9. Adjusting the Tilt Gearing:The tilt hand wheel changes the tilt angle of the blade by ro

66 SawStop 10” Industrial Cabinet SawMaking Adjustments to Your Saw10. Adjusting the Miter Gauge:The miter gauge bar includes three spring bearing

SawStop 10” Industrial Cabinet Saw 67Overall saw dimensions: 44” w x 34” d x 34” h 69 1/4”w x 36 1/2” d x 34” h (w/ optional fence & 36” rail

SawStop 10” Industrial Cabinet Saw 5WarrantySawStop warrants to the original retail purchaser of a new industrial cabinet saw from an authorized Sa

68 SawStop 10” Industrial Cabinet SawMaintenance1. SawStop Safety System:The safety system in general requires little maintenance. The system perf

SawStop 10” Industrial Cabinet Saw 69TroubleshootingProblem Possible Cause(s) SolutionThe motor will not start and both LEDs on the switch box are

70 SawStop 10” Industrial Cabinet SawTroubleshootingProblem Possible Cause(s) SolutionCannot turn saw on in Bypass mode.1. The sequence for starti

SawStop 10” Industrial Cabinet Saw 71Problem Possible Cause(s) SolutionThe blade slows down during cut, but does not stop.1. One of the belts is n

72 SawStop 10” Industrial Cabinet SawProblem Possible Cause(s) SolutionThe cuts are not even and/or clean.1. The blade is dull. 1. Replace or sha

SawStop 10” Industrial Cabinet Saw 73Cabinet Saw DimensionsFront View Rear View34"19 1/4"4 3/8"44"24"5"2 1/8"12&

74 SawStop 10” Industrial Cabinet SawCabinet Saw DimensionsLeft Side View Footprint3"12"24"30"1"33 7/8" 24 3/4"

SawStop 10” Industrial Cabinet Saw 75Push Stick ConstructionThis diagram illustrates a typical pushstick. Pushsticks should be constructed from mat

76 SawStop 10” Industrial Cabinet SawFeatherboard ConstructionThis diagram illustrates a typical featherboard. Featherboards should be constructed

SawStop 10” Industrial Cabinet Saw 77Electrical Schematic — 230V, Single-Phase (3 and 5 HP)1L1 3L25L313NO14NO2T1 4T2 6T32T1 4T2 6T395 96A2COILA1COI

6 SawStop 10” Industrial Cabinet Saw1. Read and understand the instruction manual and all safety warnings before operating this saw. Failure to fo

78 SawStop 10” Industrial Cabinet SawElectrical Schematic — 230V, Three-Phase (3, 5 and 7.5 HP)1L1 3L25L313NO14NO2T1 4T2 6T32T1 4T2 6T395 96A2COILA

SawStop 10” Industrial Cabinet Saw 79Electrical Schematic — 480V, Three-Phase (5 and 7.5 HP)1L1 3L2 5L313NO14NO2T1 4T26T32T1 4T2 6T395 96A2COIL A1C

80 SawStop 10” Industrial Cabinet SawCabinet and Table Assembly Exploded View2526333424293231288040417572747347464833141720353435553937411823212227

SawStop 10” Industrial Cabinet Saw 81No. Description Part No. Qty.1 Table CB104 001 12 Rear Lock Down Screw for Insert CB104 002 2N/A Extension Win

82 SawStop 10” Industrial Cabinet SawNo. Description Part No. Qty.36Contactor Box 3HP/208-240V/1-phase CB105 0071Contactor Box 3HP/208-240V/3-phas

SawStop 10” Industrial Cabinet Saw 83No. Description Part No. Qty.62 Belt Access Door Interlock Switch CB105 001 163 M4x0.7x30 Screw CB105 002 264

84 SawStop 10” Industrial Cabinet SawInternal Assembly Exploded View9497929031161433159536193217934351393915088495155894140421110313938535231301072

SawStop 10” Industrial Cabinet Saw 85No. Description Part No. Qty.13HP, 1PH, 208-240V, 60Hz, TEFC Motor CB104 06913HP, 3PH, 208-240V, 60Hz, TEFC Mo

86 SawStop 10” Industrial Cabinet SawNo. Description Part No. Qty.35 M5x0.8x15 Socket Head Screw CB104 107 436 M5.1x9.3 Lock Washer CB104 108 237 E

SawStop 10” Industrial Cabinet Saw 87No. Description Part No. Qty.76 5/16-18NC x 5/16 set screw CB104 148 477 Wave Washer CB104 149 178 Tilt Indica

SawStop 10” Industrial Cabinet Saw 710. Do not try to force the saw to do something it was not designed to do. For example, do not try to cut wood

88 SawStop 10” Industrial Cabinet SawArbor Assembly Exploded View3245132418171016810917101211151432333442583136293637283748495044373953513052354138

SawStop 10” Industrial Cabinet Saw 89No. Description Part No. Qty.1 Arbor Block CB104 172 12 Arbor CB104 173 13 M5x5x28 Key CB104 174 14 Main Arbor

90 SawStop 10” Industrial Cabinet SawNo. Description Part No. Qty.42 Threaded Pin CB104 213 143 Retraction Bracket CB104 214 144 Retraction Pawl CB

SawStop 10” Industrial Cabinet Saw 91This page is blank.Cabinet Saw Manual 1st Reprint.i91 91 3/9/2010 8:33:14 AM

92 SawStop 10” Industrial Cabinet SawMiter Gauge and Blade Guard Assemblies Exploded View

SawStop 10” Industrial Cabinet Saw 93No. Description Part No. Qty.Blade Guard Assembly (complete) CB104 229 11 Guard Left Half CB104 230 12 Guard R

94 SawStop 10” Industrial Cabinet SawAccessoriesSawStop recommends the following accessories for use with your SawStop cabinet saw. Contact SawStop

SawStop 10” Industrial Cabinet Saw 95IndexAAccessories: 7, 11-13, 94Accidental Contact: 10-12, 28, 31, 40, 44-45Activation of Brake (see Brake Acti

96 SawStop 10” Industrial Cabinet SawIndexBlade Guard anti-kickback pawl: 13, 34, 39, 62 guard: 7-8, 11, 13-14, 20-22, 25, 34-35, 38-39, 67, 92-9

SawStop 10” Industrial Cabinet Saw 97IndexDisconnect Switch: 7, 10, 14, 24-26, 28, 41, 45-46Dust collection: 23, 67-68 hazard: 23 port: 14, 23,